Torx Screw Size For Shark Navigator Lift-Away: A Guide (2025)

The Shark Navigator Lift-Away is a vacuum cleaner that can be challenging to take apart and repair. To disassemble the device, you will need a special screwdriver or a star-shaped security bit. The exact type and size of the screwdriver or bit required depend on the model of the Shark Navigator Lift-Away. For example, the NV352 model and other 3 series Navigators require eight screws to be removed, and a Shark vacuum screwdriver or special star-shaped security bit is recommended. Torx bits, such as the Lexivon 13 Piece Torx Bit set, are also mentioned as suitable tools for disassembling the Shark Navigator Lift-Away.

The correct Torx bit set for the job

To take apart a Shark Navigator Lift Away vacuum cleaner, you'll need a special star-shaped security bit or a Shark vacuum screwdriver. The Lexivon 13 Piece Torx Bit set and the T-Handle Hex bit holder are recommended for this task. You could also use a bit-holding screwdriver set.

If you don't already have one of these tools, you can purchase a set online. Here are some options:

• The Tonsiki 11-piece security and tamper-proof star bit set is available on Amazon.com. This set includes bits of varying sizes, from T6 to T40, and they are made of S2 steel with a magnetic, 3-inch-long tip. Reviews for this product are mixed, with some praising its sturdiness and affordability, while others complain about the bits being dull and unable to grab the screws tightly.
• The Yakamoz 11-piece magnetic T6-T40 Torx Head Screw Driver Bit Set is another option suggested by a user who successfully used it to open their Shark vacuum. This set can be purchased on Amazon.com.
• TUAKIMCE Torx Screwdriver Bits 11pcs 75mm T6-T40 S2 Steel Magnetic Star Torx Security Head Screwdriver Bits Set, available on Amazon.eu.

When purchasing a Torx bit set to take apart your Shark Navigator Lift Away, make sure to select a set that includes the appropriate size and length of bits to fit the screws on your vacuum. It may be helpful to check online forums or videos for specific recommendations from other Shark vacuum owners.

Removing the base plate

To remove the base plate of your Shark Navigator Lift-Away, you will need to remove eight screws in total. Note that two of the screws are located under the front wheels, and two are between the large back wheels. You will need a special star-shaped screwdriver bit for this task, such as the Lexivon 13-Piece Torx Bit Set or a T-Handle Hex Bit Holder. A bit-holding screwdriver set can also be used.

First, remove the two screws under the front wheels. Pop off the small wheels using a flat-head screwdriver to access the screws underneath. Next, remove the two screws between the main back wheels. After removing these four screws, the remaining four are located on the bottom of the cleaning head. On older models, these screws are Phillips-head, while on newer models, they are Tonsiki. Once all eight screws have been removed, the base plate should lift off easily.

At this stage, you will have access to the brush bar, belt, small hose, circuit board, and brush motor. The brush bar can be lifted out easily, and the belt will unhook from the motor.

Removing the brush roll motor

To remove the brush roll motor from your Shark Navigator Lift-Away, you'll need to first remove the base plate to access it. Here's a detailed guide on how to do it:

Removing the Base Plate:

Start by locating the eight screws that secure the base plate in place. Two screws are hidden under the little front wheels, and another two are between the large back wheels. Remove these screws using a Shark vacuum screwdriver or a special star-shaped security bit like the ones found in the Lexivon 13-piece Torx bit set. With the screws removed, you can now lift off the base plate.

Once the base plate is removed, you'll have access to the brush roll motor. On newer models of the Shark Navigator Lift-Away, there are two screws at the side of the motor that need to be removed. After removing these screws, you can carefully lift out the motor. If you have an older model, your motor may not have these side screws, so you can simply lift it out without any trouble.

Detaching the Circuit Board Leads:

Now that the motor is out, you'll need to detach the circuit board leads from the motor contacts. Use a pair of needle-nose pliers to carefully remove the leads. Be gentle to avoid damaging the delicate components.

Completing the Brush Roll Motor Removal:

With the circuit board leads detached, you have now successfully removed the brush roll motor from your Shark Navigator Lift-Away. Remember to keep track of the screws and their locations for easier reassembly. If you're replacing the motor, you might also want to consider replacing the circuit board, especially if there were any faults with your vacuum cleaner.

Remember, before attempting any repairs or maintenance on your vacuum cleaner, make sure to unplug it and ensure it is turned off to avoid any accidents or injuries. Always refer to the official manufacturer's instructions or seek professional assistance if you're unsure about any steps.

Removing the circuit board

To remove the circuit board of a Shark Navigator Lift Away, you will first need to remove the base plate. There are eight screws to remove in total. Note that two of the screws are under the front wheels, and two are between the large back wheels. You will need a special star-shaped screwdriver for this, such as the Lexivon 13 Piece Torx Bit set or a T-Handle Hex bit holder.

Once the base plate is removed, you will have access to the brush bar, belt, small hose, circuit board, and brush bar motor. The brush bar lifts out easily, and the belt will unhook from the motor.

The next step is to remove the brush roll motor. Newer models have two screws at the side that need to be taken out, while older models do not have these screws, and the motor can be lifted out. After removing the motor, use a pair of needle-nose pliers to remove the circuit board leads from the motor contacts.

Now you are ready to remove the circuit board. It is held in place with two screws. If you are replacing the brush motor, it is recommended to replace the circuit board as well, as it could be responsible for any faults.

At this stage, you should be able to remove the whole swivel unit from the base plate.

Removing the side latches

To remove the side latches from your Shark Navigator Lift-Away, follow these steps:

First, remove the HEPA filter and the cover at the front of the vacuum. Lay the motor housing down on its front side. You will see dowel pins holding the latches in place. Push down on these pins to disengage them. A certain amount of pressure is required, but not so much that you need a hammer. You may find it helpful to use a center hole punch to disengage the pins.

Once the latches are removed, take out the top filter.

If you are removing the side latches in order to access the motor, the next step is to remove all the screws from the motor housing. There are six screws in the front plate, including one hidden behind the 'loss of suction' sticker, and two screws around the back of the handle holder. Then, turn the vacuum over and remove the ten screws in the base. This will allow you to release the motor from the housing.

If you are disassembling your Shark Navigator Lift-Away for the first time, it is recommended that you video yourself doing it. This will be helpful when it comes to reassembling the vacuum.

Frequently asked questions